Echo chainsaw problems

Having your own chain saw can be incredibly helpful when it's time to do more intensive lawn and yard work, but despite their use in a lot of rugged, messy jobs, chain saws are more sensitive machines than many owners realize. It can be incredibly frustrating when it fails to start, especially if you've invested in a high-quality, top-of-the-line chain saw.

Thankfully, a chain saw failing to start is a common problem with generally simple solutions. There are a variety of ways to solve the issues that are causing your chain saw to fail and a few good practices you can follow to avoid having the problem in the future.

Nearly all of the mechanics and functions of a chain saw are built around the firing of its engine. If the engine isn't chugging along, the assembly of gears that pull the chain you use to cut won't work. So, if your gas chain saw isn't starting, it's likely that gas isn't feeding into the engine properly.

Before you start troubleshooting, however, it's worth knowing just how the chain saw's engine works. A gas-powered chain saw's engine functions much like that of a car. Simply put, the piston that drives the gears and chain is powered by energy released by combustion.

Fuel in the tank is mixed with air when it's pulled into the carburetor where it's then ignited by a spark from the spark plug. If your chain saw isn't getting gas, the trouble most likely lies in one of those three core components: the fuel tank, the spark plug or the carburetor, or one of the minor parts adjacent to the three.

The first place to check when troubleshooting issues with your chain saw's gas intake is the fuel tank itself. Beyond making sure that an adequate amount of gas is in the tank, consider the last time your chain saw was started.

If it's been longer than a month and you didn't empty the fuel tank before storing it — especially if the chain saw has been sitting in a cold area — it's possible that the problem could be the result of fuel degradation. The gas in a chain saw's fuel tank doesn't last forever.

In as short as 30 days, the gas eventually separates into different components. This doesn't only hinder the engine's fuel combustion process but can clog the carburetor and run the risk of fouling the spark plug. As a result, it's best to always use fresh fuel and empty out your chain saw's tank if you won't be using it again for more than three weeks.

To clean out your chain saw's gas tank, empty it, swish some fresh gas around inside it do not attempt to use water and then scrub it with a wire brush and thin rag.The Echo CS is a powerful standard gas-powered chainsaw. The inch bar is strong enough to fell trees, but small enough to store in a garage.

How to Adjust the Oiler on an Echo Chainsaw

The When we tested this saw, our lab team had several things to say about it. Echo uses an i30 starting system for quick ignition. We started each chainsaw for the first time out of the box. We noted how long it took each one to start with just one pull of the cord — the Echo took four attempts. This is good, but not the fastest we saw in our test — Husqvarna only took three attempts while the Poulan Pro took seven. The Echo chainsaw cut through our test log at high speeds, averaging just under five seconds per cut.

However, its noise level reached around 90 decibels. That being said, you should always wear hearing protection when operating any chainsaw.

These materials may bend if strained, but they keep the saw light and easy to handle. We used the chainsaw to clear out an overgrown yard with half dead bushes, dead trees, stumps and more. We were impressed at how well the Echo cut through everything in its path with relative ease, even on a hard, dried cherry tree stump — which several of our corded models struggled mightily with. Users consistently praised the Echo for its small, light frame which made it perfect for small jobs around the garden such as tree limb cleanup.

Another user noted issues with claiming against the warranty when the saw broke down, so be mindful of this. Parts and repairs are available for the Echo saw from large home improvement stores and licensed dealers alike.

echo chainsaw problems

This provides the option to visit a specialty store or a large chain, depending on the services available in your area. Some chainsaw brands require licensed professionals to perform maintenance, which increases the chances of your chainsaw being repaired correctly the first time versus making multiple trips to the home improvement store for new parts.

echo chainsaw problems

Luckily, this saw is under warranty for five years. Rather than including items like a chain or sharpening tools, you must visit these specialists to find exactly what the model needs.

Echo Chainsaw Clinic - CS-670 cutting and starting issues fixed - On The Homestread EP17

In the box, there are essentials like an owner's manual, scrench, bar scabbard and engine oil. Although there is no carrying case included with this model, Echo dealerships provide cases, files and other accessories you may need. The Echo CS is light and starts quickly, making it a suitable chainsaw for professionals, power tool lovers and rural homeowners. Best Chainsaws of Top Ten Reviews has reviewed the Best Chainsaws of so that we're able to offer you the authoritative buying advice you expect.

Home Reviews. For Light Well balanced Provides clean cut. Against Overkill for home users.

Image 1 of 4.When the saw dust settled, the Echo 58V Chainsaw took first place among the 8 contestants in cut speed as well as run time and efficiency.

I recently had all kinds of fun conducting a shootout of eight battery-operated chainsaws for Pro Tool Reviews. As I mentioned at the time, I did a similar test four years ago but the field was much thinner due to the relative lack of power compared to what we have today.

Now, more manufacturers are competing as battery technology improves and consumers have seen how lithium-ion technology can approach and sometimes even exceed their petrochemical AKA gas counterparts.

The Echo 58V Chainsaw is a volt, 4. Its battery powers a brushless motor and it features and automatic oiler, a mechanical lockout switch, inertia chain brake, variable speed trigger, dual bar studs, and a built-in wrench storage slot.

This is the only saw that includes an optional tip guard to protect against kickback. Bucking spikes, resembling teeth and typically made of metal on gas-powered chainsaws, are meant to grip the wood or bark as the chain makes a vertical cut through a horizontal log. For a full description of how I tested the saws, be sure to check out the shootout.

Likewise was its felling grip performance rated Very Good. It turned out that the best trigger of the group of 8 chainsaws belonged to the Echo as well. Other saws left the trigger protruding when squeezed, which can cause discomfort over long periods of use.

Even though the Echo had the lowest battery capacity among the top three chainsaws, it ranked first in the runtime by making 97 cuts on one charge, or the equivalent of nearly 0. It also scored the fastest cutting speed through an 8-inch pine log at 5. The Echo 58V Chainsaw features a 4. It has a brushless motor, automatic oiler, a mechanical lockout switch, inertia chain brake, variable speed trigger, dual bar studs, and a built-in wrench storage slot.

It alone earned Very Good ratings for both bucking and felling grips. Craftsman and writer Michael Springer specializes in testing tools and covering the tool industry for construction and woodworking professionals. Based in Boulder County, Colorado, but going wherever the story takes him, Michael crisscrosses the country yearly to visit manufacturers and attend trade shows, and occasionally gets as far afield as Europe.

Echo CS-310-14 Review

Menu Skip to content. Cutting Speed. Battery Efficiency. Feature Set. Final Thoughts When the saw dust settled, the Echo 58V Chainsaw took first place among the 8 contestants in cut speed as well as run time and efficiency. Overall Score 4. Want more? Join our newsletter and get the latest tool reviews every week!Chainsaw guide bar and chain oil performs the very important task of keeping the guide bar lubricated where the chain rides around it.

Correct lubrication keeps both the chain and guide bar cool, preventing overheating and warping from friction. An Echo chainsaw oiler is preset at the factory but can be adjusted to increase or decrease the oil flow. The proper adjustment procedure includes testing the oiler after each turn of the adjustment screw.

Release the throttle trigger on your Echo chainsaw to stop the chain rotation. Push the ignition switch on the left, rear of the engine down to the "Off" position to stop the engine. Turn the chainsaw on its left side, with the guide bar and chain pointing upward. Insert a small, flat-head screwdriver into the oil-adjusting screw. The oil adjusting screw is just below the base of the chain and guide bar.

Echo CS-400 Chainsaw Review: You NEED To Read This!

Place newspaper on the ground in an open area. Put on safety glasses, earplugs and leather work gloves. Start your chainsaw's engine as you normally do.

Squeeze the throttle trigger to make the engine operate at about one-half speed, pointing the tip of the chainsaw at the newspaper for about 30 seconds. The chainsaw should throw a light film of oil. Stop the chainsaw's engine. Increase the oil flow by turning the oil adjusting screw counterclockwise if very little oil sprayed on the newspaper.

Decrease the oil flow by turning the oil adjusting screw clockwise if large splatters of oil dropped on the newspaper. Make small, incremental adjustments by turning the oil adjusting screw slightly until the chainsaw sprays a light splatter of oil on the newspaper. Mary Lougee has been writing for over 10 years.

echo chainsaw problems

She holds a Bachelor's Degree with a major in Management and a double minor in accounting and computer science. She loves writing about careers for busy families as well as family oriented planning, meals and activities for all ages.

Skip to main content. Wait for the engine to cool completely. Tips Check the chain and guide bar lubrication before each use of a chainsaw. Fill the guide bar oil and gasoline tanks before each use of the chainsaw.

A small amount of oil should be in the saw's tank when it runs dry. Warnings Start a chainsaw on the ground without the chain contacting any debris on the ground.Echo chainsaw products are well known for their reliable performance and professional cutting. They are commonly used for all kinds of yard maintenance as well as professional tree felling duties because of their excellent cutting capabilities and durability.

Reviewing such a broad range of products is never going to be easy and ultimately it will come down to what you mainly intend to use a chainsaw for.

That said hopefully we can shed some light on which of these models is best for specific usage and frequency of use. In some shape or form the company have been around since A company with this kind of provenance clearly has expertise in their chosen field. The Echo brand is a premium offering in the chainsaw market. As such many of the models reviewed here share some features many of which are standard across the Echo brand. Put simply the mechanics of the product incorporate a helper spring that is wound as you pull the starter cord.

Upon reaching a certain tension the energy is released aiding the engine to start. Even with a slow pull Echo Chainsaws will start. It is fair to say that other manufacturers such as Husqvarna have similar technologies. All of the Echo models on test include automatic oiling and some are also adjustable. This is one less thing for you the operator to worry about. Here is our list of Echo chainsaw reviews. This list should help you narrow down your options so you can easily pick out the best Echo chainsaws for your requirements.

The Echo CS T comes with a 12 inch bar and chain making it ideal for light to medium-heavy duty cutting. It features a G-Force Engine Air Pre-cleaner purposely made in order to lessen the maintenance of its air filter. Using the chain tensioner that is conveniently located at the side, you can make quick adjustments to your chain. It also employs the i system, promoting a quick start to its The clutch-driven oiler will automatically close in order to control excessive oil consumption.

One of the main things of note with this chainsaw compared to the others on review is that it has a top handle. With this unit being so light and nimble many will use this single handed. This is great for limbing and pruning but could be dangerous in the wrong hands hence Echo only recommend this saw for tree service professionals.

The Echo CST is a bit expensive compared to your regular chainsaw but this is because it belongs to one of the top performing brands and this model includes a raft of useful features. Overall this is a lightweight chainsaw that gives you the best comfort while pruning trees and bushes.Pruning trees, cutting firewood, or clearing shrubs and brush from an area can be difficult if you only have manual tools, such as a handsaw, pruning shears or an axe to choose from.

Your Echo chainsaw can replace all those hand tools and help save you some time when it comes to completing your chores. Make sure you prepare the chainsaw before operating. This will ensure you start the chainsaw correctly and avoid any damage to its motor.

Add 2. Screw the lid on the gas can and shake it to mix the engine oil and gas together. Find the stationary handle on top of the motor near the chain bar and chain. Look for the chain-brake lever between the stationary handle and the chain bar and chain.

Push the chain-brake lever away from the motor and toward the tip of the chain bar. The chain-brake lever stops the rotation of the chain around the chain bar. Remove the fuel cap from the chainsaw engine. Fill the fuel tank with the 2-stroke engine oil and gas mixture. Replace the fuel cap and twist it clockwise to tighten it.

Remove the cap from the chain bar oil tank. Fill the oil tank with Echo bar and chain oil and replace the oil tank cap. Place the Echo chainsaw on firm ground. Find the ignition switch at the rear of the motor to the left of the rear handle and throttle. Look for the soft rubber purge pump bulb on the rear of the motor to the right of the rear handle.

The choke's control knob is directly beneath the purge pump bulb. Use your thumb to press the rubber bulb toward the motor three or four times, or until you see a small amount of gas appear inside the bulb. Pull the choke control knob out from the motor. Find the starter handle on the left side of the motor. Place one hand on the stationary handle as you quickly pull the starter handle from the motor. Continue to pull the starter handle three or four times or until you hear the motor attempt to start.

Push the choke control knob back into the motor. Reposition your hands on the chainsaw and quickly pull the starter handle once more to start the motor, and allow it to idle. Carefully lift the chainsaw with both hands and press and release the trigger in the rear handle to release the idle throat latch. Restart a warm Echo chainsaw motor by pushing the chain-brake lever toward the tip of the chain bar.

Place the chainsaw on the ground and pull the starter handle. Immediately press and release the trigger once you hear the motor start idling. Cecilia Harsch has been writing professionally since Everyone encounters problems with their chainsaw on occassion, and most of the issues that come up can be resolved fairly easily.

And so, I thought I would share some of the knowledge I have gained over the years. Let me start by saying that many problems can be avoided just by doing some simple, regular maintenance on your saw.

Things like cleaning the air filter, putting fresh gas in the saw, remembering to add bar and chain oil when you fuel up, and running a file over your chain every tankful of gas or two. Problems with how the chain cuts can usually be associated with the quality of the sharpening. If the chain cuts crooked or at an angle, then you are filing the cutters at different angles or applying inconsistent pressure on one side over another.

The angle of the top plate and the size of the cutter should be very consistent throughout your chain. If your chain dulls quickly, then it could be a couple of things.

Alternatively, you could be applying too much pressure when you file. This will create cutting edges that are too thin and dull quickly. Your chain will cut too deep or barely cut at all if your rakers or depth gauges are filed down too much or not enough, respectively.

Get yourself a depth gauge appropriate for your saw and use it every time you sharpen your chain. If the filter is clogged, the ratio of air to gasoline in the carburetor will be off. This can lead to a fouled spark plug and a clogged spark arrester screen inside the muffler. Some of the best advice I got was to never mess with the carburetor unless you really know what you are doing.

You may need to replace the spark plug if this condition has been going on for a while. Finally, sometimes your chain will seem like it is not getting enough oil. When I first learned to use a chainsaw, I was taught to rev the engine a bit before cutting. If the chain was getting sufficient oil, a bit of the oil will fly off the end when the engine is revved. The solution to this problem is pretty simple.

After you finish using your saw for the day, take the bar and chain off and clean out all the debris that has accumulated around the oiling mechanism. You can check to see if you have cleaned the oiling mechanism thoroughly by running your saw without the bar and chain on and watching to see if oil comes out. If you do the prescribed regularly scheduled maintenance and sharpen your chain correctly, you can avoid the problems I have described here.


thoughts on “Echo chainsaw problems

Leave a Reply

Your email address will not be published. Required fields are marked *